A tablet can make a long drive easier for everyone in the back seat. Children can watch a movie, passengers can follow a travel route, and families can share downloaded shows without someone holding the screen for hours.
The problem often starts when the tablet has nowhere to stay. It slides across the seat, rests on a passenger’s lap, or ends up attached to a mount that sticks out even after the drive is over.
The Lamicall STCH05 Lockable Foldable Clip Car Headrest Tablet Holder is designed to give the tablet a fixed place behind the front seat. Its metal headrest crossbar, adjustable biaxial arm, tightening knob, and foldable device clip create a setup that can be repositioned during the trip and folded away afterward.
Quick Answer
The Lamicall STCH05 is a foldable car headrest tablet holder made for vehicles with exposed headrest rods. It supports phones and tablets up to 13 inches, while its biaxial extension arm lets rear-seat passengers adjust the viewing distance and angle.
When the screen is no longer needed, the device clip folds inward to reduce the amount of hardware extending into the back-seat area.
What Makes a Headrest Tablet Holder Easier to Use?
A back-seat tablet holder needs to do more than grip a screen. It should stay connected to the headrest, let passengers position the device without rebuilding the mount, and avoid taking over the back seat when it is not being used.
The STCH05 addresses these everyday details through three parts of its design:
- A metal crossbar connects the holder to the headrest rods.
- A biaxial extension arm adjusts the screen’s position.
- A foldable clip retracts when the device is removed.
Each feature solves a different part of the same problem: giving rear-seat passengers a practical viewing position without adding unnecessary clutter.
Adjust the Screen Without Moving the Entire Mount
Seat positions can change from one trip to the next. A child may sit closer to the front seat, two passengers may want to share the screen, or an adult may need more distance between their eyes and the tablet.
The STCH05 uses a biaxial extension arm rather than holding the device in one fixed position. The arm can be adjusted to change the viewing distance and angle, while a tightening knob helps hold the selected position.
This makes it easier to move the screen toward one side of the back seat or position it closer to the center, depending on the vehicle layout and the passengers using it.
Before driving, adjust the tablet while the vehicle is parked. Tighten the knob and check that the arm and device clip remain in place.
A Metal Crossbar Creates a More Direct Connection
A tablet mount is only as useful as the point where it connects to the vehicle.
The STCH05 attaches to the exposed rods beneath the front-seat headrest. Its metal crossbar spans the space between the rods, while deeper hooks at both ends help maintain contact with the mounting points.
Rubber contact areas also help reduce slipping and prevent the holder from rubbing directly against the tablet.
Instead of balancing the device on a seat or handing it between passengers, the tablet remains attached to a defined position behind the headrest.
Fold the Clip Away After the Movie Ends
A mount that works well during a movie can still become an annoyance when the screen is removed. A large clip left open behind the seat may take up passenger space or catch on bags when someone enters the vehicle.
The STCH05 uses a foldable tablet clip that retracts when it is not needed. Once the tablet is removed, the clip can be folded inward so that it sits closer to the rest of the holder.
This small detail is especially useful in vehicles that alternate between family trips, daily commuting, school runs, and carrying luggage. The holder can remain attached without leaving the full device clamp extended into the seating area.
Check Your Tablet and Headrest Before Ordering
“Universal” does not mean that every mount fits every device or vehicle. A few measurements can prevent compatibility problems.
Device Compatibility
The STCH05 is designed for smartphones and tablets up to 13 inches.
The holder supports:
- A device or case thickness of up to 0.9 inches, or 23 mm
- A suitable screen-width range of approximately 4.6 to 9.2 inches
- Common tablets, e-readers, phones, and similar devices within the supported dimensions
This includes many models from the iPad, Galaxy Tab, Kindle, and Fire HD families. Device generation alone should not be used to confirm compatibility. Measure the tablet with its case installed, particularly when using a thick protective case.
Vehicle Compatibility
The supported distance between the two headrest rods is:
- 2.8 to 6.1 inches
- 72 to 155 mm
The headrest hooks are designed for rods with a diameter of approximately 12 mm.
The STCH05 requires exposed headrest rods. It is not designed for seats with integrated headrests or seats where the rods are fully covered and inaccessible.
A Practical Setup for Family Road Trips
On a long drive, small adjustments can make the back seat feel less crowded.
A mounted tablet gives the screen a fixed position, leaving passengers’ hands free for snacks, blankets, books, or travel games. The adjustable arm also means the device does not have to remain pressed close to the front seat.
For families traveling with children, the holder can support downloaded movies or educational videos without placing the tablet on a child’s lap. For adult passengers, it can hold navigation information, entertainment, or reading material at a more consistent position.
The mount should only be adjusted while the vehicle is safely parked. Drivers should not watch or operate a rear-seat entertainment device while driving.
How to Prepare the STCH05 for a Trip
Before the first journey, take a few minutes to check the complete setup.
1. Measure the Headrest Rods
Measure the distance between the two exposed rods and confirm that it falls within the supported 2.8-to-6.1-inch range.
2. Check the Device With Its Case
Measure the device at its widest and thickest points. Thick children’s cases, keyboard cases, and covers with handles can change the final dimensions.
3. Attach the Holder to the Headrest
Install the metal crossbar according to the included product instructions. Confirm that both ends are properly engaged with the headrest rods.
4. Position the Extension Arm
Move the biaxial arm until the tablet is at a suitable distance and angle for the passenger. Tighten the adjustment knob before inserting the device.
5. Secure the Tablet
Place the tablet inside the clip and confirm that the rubber contact areas sit correctly against the device or case.
6. Check the Setup Before Driving
With the vehicle parked, gently check the holder, extension arm, and tablet. Make sure the mount does not interfere with seat belts, headrest adjustment, doors, or passenger movement.
When Is the STCH05 Most Useful?
The STCH05 is well suited to drivers who regularly carry rear-seat passengers and want a holder that does not need to be removed after every trip.
It can be useful for:
- Family road trips
- School and daycare journeys
- Long-distance travel
- Rear-seat movie viewing
- Shared tablet viewing between passengers
- Vehicles that need a more flexible screen position
- Drivers who prefer a foldable holder instead of a permanently open clamp
The adjustable arm is particularly helpful when the passenger position changes frequently. The foldable clip is useful when the same vehicle is also used for commuting, shopping, or carrying luggage.
A More Organized Place for Back-Seat Entertainment
The STCH05 does not turn the back seat into a complicated entertainment system. It simply gives the tablet a more practical place to stay.
The metal crossbar connects the mount to the headrest rods. The biaxial arm lets passengers adjust the viewing position. The foldable clip retracts when the screen is removed.
Together, these features help keep the device off passengers’ laps and reduce the amount of unused hardware extending into the back seat.
View the Lamicall STCH05 Foldable Car Headrest Tablet Holder
Frequently Asked Questions
Does the STCH05 fit cars without exposed headrest rods?
No. The mount requires two accessible headrest rods. It is not suitable for integrated headrests or seats where the rods cannot be reached.
Can it hold a tablet with a protective case?
It can support a device and case combination up to 0.9 inches, or 23 mm, thick. Measure the tablet with the case installed before ordering.
Does it support 13-inch tablets?
The product is designed for devices up to 13 inches. Compatibility also depends on the tablet’s width and thickness, so confirm all three measurements rather than relying only on the advertised screen size.
Can the holder be folded when it is not being used?
Yes. The tablet clip can be folded inward after the device is removed, helping reduce the amount of space the holder occupies behind the seat.
Can two rear-seat passengers share one tablet?
The biaxial arm allows the screen position and viewing distance to be adjusted. Whether two passengers can view the screen comfortably depends on the vehicle width, seat positions, and tablet size.
Should the mount be adjusted while driving?
No. Install and adjust the holder while the vehicle is parked. The driver should not operate or watch the mounted device while driving.
